Page 9 of 13
Re: Ted’s knife thread
Posted: Mon Dec 14, 2020 5:58 am
by bimbo
Top work on the hollow grinds Ted, takes some skills to get even grind lines like that. What size contact wheel are you using to do them?
Sent from my Pixel 3 using Tapatalk
Re: Ted’s knife thread
Posted: Mon Dec 14, 2020 12:54 pm
by deermasterhunter
bimbo wrote: ↑Mon Dec 14, 2020 5:58 am
Top work on the hollow grinds Ted, takes some skills to get even grind lines like that. What size contact wheel are you using to do them?
Sent from my Pixel 3 using Tapatalk
Thanks James, I'm using a ten inch wheel mate, makes it a lot easier. I used a 12inch wheel for the first one, but the ten inch suits me better and swapped my 12inch one for a 10 inch one off my mate. I just used some more of your scales on the Cleaver below
NEW AND OLD CLEAVER
Made this cleaver again from the probably near 100year old large saw blade. It's great steel in it and slowly using it up. Handle is some scales that Bimbo made for me and pins are aluminium. So it's a real old and new Cleaver. Probably got some rain spots on as was raining while taking photos.
Re: Ted’s knife thread
Posted: Wed Dec 16, 2020 7:23 pm
by deermasterhunter
I decided to do a couple more knives this afternoon after a hard mornings work. Trying to free hand grind the buggers is hard. I had this one nearly finished and decided to get the last little bit on film. You can see one of the ways how I do it anyway. And what it looked like when it was finished. It's not perfect, sort of went up a tad too far at the ricasso on one side. But a blind man won't be able to see it. Er!! wait a minute
%5Burl%5Dhttps%3A//www.youtube.com/watch?v=1CEil4YYGhQ&ab_channel=tedMitchell%5B/url%5D
https://www.youtube.com/watch?v=1CEil4Y ... edMitchell
https://www.youtube.com/watch?v=ByEAaYR ... edMitchell
Re: Ted’s knife thread
Posted: Fri Jan 01, 2021 7:20 pm
by deermasterhunter
Just finished Giveaway number 120 a good start to the new year
Re: Ted’s knife thread
Posted: Fri Jan 01, 2021 7:42 pm
by dashooter
deermasterhunter wrote:Just finished Giveaway number 120 a good start to the new year
Very nice work (as always) Ted.
Sent from my iPhone using Tapatalk
Re: Ted’s knife thread
Posted: Fri Jan 01, 2021 7:51 pm
by mick_762
Yep gotta agree Rob, very nice (as usual).
Sent from my SM-G930F using Tapatalk
Re: Ted’s knife thread
Posted: Fri Jan 01, 2021 9:44 pm
by daisy
Re: Ted’s knife thread
Posted: Sat Jan 02, 2021 7:18 am
by fenring
Nice work young Ted.
Re: Ted’s knife thread
Posted: Sat Jan 02, 2021 10:23 am
by deermasterhunter
Probably get lost in the post the same as the last one I sent you mate.?
fenring wrote: ↑Sat Jan 02, 2021 7:18 am
Nice work young Ted.
Thanks Scott, hope your keeping well mate. Happy new year to you and the family and also to everyone else on AusVarmint
dashooter wrote: ↑Fri Jan 01, 2021 7:42 pm
deermasterhunter wrote:Just finished Giveaway number 120 a good start to the new year
Very nice work (as always) Ted.
Sent from my iPhone using Tapatalk
Thanks Rob, I keep on trying
mick_762 wrote: ↑Fri Jan 01, 2021 7:51 pm
Yep gotta agree Rob, very nice (as usual).
Sent from my SM-G930F using Tapatalk
Thanks David
Re: Ted’s knife thread
Posted: Sat Jan 02, 2021 7:37 pm
by deermasterhunter
Finished this Damascus knife today. Scales by Bimbo gee he makes some lovely scales. This one is for sale if someone wants a nice Damascus knife as I need some money
Re: Ted’s knife thread
Posted: Mon Jan 04, 2021 12:56 pm
by deermasterhunter
I made this one as I see quite a few knives with the flatter bottom and the top spine heading down rather that the blade heading upwards at the end. It's really different to what I normally make and I might just make a few more and change the angle at the end a bit to see how they look.
Made this on from 1084 high Carbon steel and put Dead Finish timber scales on it. Gee its nice timber but hard as the hobbs of hell.
Hollow ground this one and believe it or not I stuffed one grind a tad with a bit of a divot, but hard to see I suppose.
Pins and Lanyard pin are brass. This should be a really handy user I reckon
https://www.youtube.com/watch?v=e7wdhdW ... edMitchell
Re: Ted’s knife thread
Posted: Mon Jan 04, 2021 12:58 pm
by deermasterhunter
[quote=deermasterhunter post_id=276782 time=1609729003 user_id=4208]
Re: Ted’s knife thread
Posted: Mon Jan 04, 2021 12:59 pm
by deermasterhunter
Double post sorry
Can a mod delete the last two posts with nothing on them please. Thanks Keith
Re: Ted’s knife thread
Posted: Tue Feb 02, 2021 7:35 am
by deermasterhunter
Re: Ted’s knife thread
Posted: Sat Feb 06, 2021 6:43 pm
by deermasterhunter
[/BBvideo][/BBvideo]Did this one from NitroV with some Hybrid scales. We thought the scales were buggered as got too hot when stabilising them, but they actually came out quite good looking like Ebony. Brass pins and this one is hollow ground,, thanks for looking This one is for sale a great caping, rabbit come fox knife Trying to work out how to make video play without clicking on it??
https://www.youtube.com/watch?v=LEjUfQb ... edMitchell