CZ 527 20VT on a budget plus DIY stock

[B4408]

Big G, it is on its way home, need to make some time to go pick it up. Been crook the last week so have to catch up on some things.
It will just need bedding in the stock and turn some necks to fit the chamber. Have 2207, 32gn zmax ready to go. No reason it wont be a shooter if I do my part.

Bruce

[kickinback]

Your part will be putting 18.5gr of that there 2207 in the case. Everything else will be just fine.


Sent from my iPhone using Tapatalk

[B4408]

Barrelled action is now home and tested some of my formed brass while at Missed's, chambered ok but may need a frac more turned off the neck. Will do the final barrel inletting tomorrow and get it bedded, finish some more brass and load it during the week.
Looking good for testing next weekend.
Bruce

[B4408]

A couple of pics of the action and barrel rough fitted in stock , a bit of bedding and tidy up for clearance along barrel to go.

IMG_0422a.jpg (165.89 KiB) Viewed 568 times

IMG_0425a.jpg (189.96 KiB) Viewed 568 times

Bruce

[Camel]

Looks good together Ruce, nice job.

[kickinback]

Well done Bruce.


Sent from my iPhone using Tapatalk

[MISSED]

The pictures do not do it justice

[matang]

Looks great. I would be happy to own it. Even more so if I had buit my own stock. What barrel profile?

[B4408]

Looks great. I would be happy to own it. Even more so if I had buit my own stock. What barrel profile?

Its a Howa 204 sporter take off barrel with a skim to remove the old calibre designation and about 10-12mm shorter to get a clean chamber and throat cut.

Kickin, it has come up a treat. Grinning every time I look at it.

Thanks Missed and thanks for dinner.

Bruce

[stinkitup]

Bruce that looks fantastic!

Love the stock design and your checking looks magic.

Well done!!

Ryan

[brahman]

congrats on the hard work and the result looks awsome

[B4408]

It went bang.

Finally got the action bedded in the stock last night and cleaned it up this morning. Popped out quite nicely.
Have had a problem with my 20VT body die during the week. It was tight on the cases from the case web down. Kept jamming cases, tried different lubes etc. The ADI 223 brass didn't want to fit, tried a Fed case and it was tight but worked. After trying a few work arounds and calling Kickin and Missed I was sick of sitting in the freezing cold in the shed.
So this morning after getting the stock sorted I tried again with the Body die. WTF it sized the brass all the way, tight but no stuck case and pushed the shoulder back to allow me to chamber easily. All I can put it down to is a much warmer day and a bit of expansion in the die, everything else was the same. Will test again in the cold in the morning, it is going to be a big frost here.
Loaded up a few cases with ADI 2207, 32gn Zmax, Rem 7.5 primers and a quick trip to a friends paddock.
Started at 17.5, 18.0, 18.3 and 18.5gn which filled the case and was a compressed load.
A few pics of targets shot at 100m, (a couple of 5 shot groups for DSD). Targets have 1moa squares.

17.5gn ADI 2207

IMG_0427a.jpg (72.13 KiB) Viewed 500 times

18 and 18.3gn ADI 2207

IMG_0426a.jpg (82.94 KiB) Viewed 500 times

18.5gn ADI 2207

IMG_0428a.jpg (77.14 KiB) Viewed 500 times

Rem 7.5 primers from Left 18.0, 18.3 and 18.5gn

IMG_0433a.jpg (97.05 KiB) Viewed 500 times

With a bit of consistency on my part I think it will shoot OK. Kickin do you reckon it will be good enough . It was a relief to finally get to pull the trigger and get a good result.
Now to finish neck turning and a bit more testing at the higher loads.

Bruce

[mick_762]

18.3gn looks bloody good - I assume extraction was easy?

Good looking rifle, stock work to be proud of and it shoots - what's not to like mate.

[B4408]

A couple of pics of the assembled rifle wearing a Nikon 3-9x40 EFR I had spare. Not sure what scope it will end up with, started putting a few $ in the shooting jar.

CZ 527-2 20VT

IMG_0429a.jpg (74.34 KiB) Viewed 499 times

CZ 527-2 20 VT with custom rosewood stock

IMG_0431a.jpg (127.17 KiB) Viewed 499 times

Special thanks to a few people who assisted along the way, I think they new more about what I wanted/needed than I did, I just followed their advice. Thanks.

Bruce

[B4408]

Thanks Mick (in more ways than one).
I wont draw conclusions on which load to use until I try run a few more through it and get use to the rifle but I think there is potential. I was kneeling at the bench as I forgot my stool in the excitement
Bruce